- MANUAL ABAQUS 6.14 INSTALL
- MANUAL ABAQUS 6.14 UPDATE
- MANUAL ABAQUS 6.14 VERIFICATION
- MANUAL ABAQUS 6.14 TRIAL
- MANUAL ABAQUS 6.14 PROFESSIONAL
I am struggling to find what they re referring to and how I should go about fixing this.
MANUAL ABAQUS 6.14 UPDATE
Intel(R) Compiler 16.0 Update 1 (package 146)Ībaqus/Explicit with user subroutines (double precision) All rights reserved.Ĭopyright (C) 1985-2015 Intel Corporation. Intel(R) MPI Library 5.1 Update 2 for Windows* Target Build Environment for Intel(R) 64 applicationsĬopyright (C) 2007-2015 Intel Corporation. I tried to verify and received the following: I have followed the instructions given here: Īs well as the instructions given in the attached document (it is not my own). I am hoping that it can work and possibly there may be a solution to my problem. The combination that I have has not been shown to work, at least I am unaware of it. From all of the methods discussed I gathered that specific programs perform well while others have not been tested. I have read through and performed most of the steps that have been proposed here and elsewhere. I am struggling to Link Visual Studio 2015, Intel Parallel Studio XE 2016, and Abaqus 6.14 in order to use Subroutines. However, I do not understand exactly “Be sure to include the "user" parameter on the Abaqus command line to identify the user subroutine file”. Let me built a small case so that I can test it from that command window. Yes, you are right I can open the Fortran initialized command window and I suppose this will initializes all the Fortran environment variables as you mentioned.
MANUAL ABAQUS 6.14 VERIFICATION
Verification directory C:\\verify has been deleted
However, when I do check for –user_std I only pass the Abaqus/Standard with user subroutines then this And yes I can avoid checking for the entire verification. I am planning on built my UMAT subroutines.
MANUAL ABAQUS 6.14 INSTALL
I wanted to pass the install verification since it was a requirement in the different forums so that you would be able to run subroutines. Yes, I do have many versions of Abaqus and VS, however I do have only the 2016 Intel Fortran Parallel Studio XE 2016 and the old version 10.1.011. The question is how could I assign the latest compiler? Yes, I agree it looks like I am running the 10.1. I also recommend writing a main program to run and test a user subroutine separately from Abaqus. Is there a user subroutine that you plan to use? If you're getting started with user subroutines in Abaqus you could create a mesh that uses DLOAD to apply element face pressure (traction) loads, since that is one of the easier user subroutines to use. Be sure to include the "user" parameter on the Abaqus command line to identify the user subroutine file. And then I run the Abaqus job from the command line. I've also had good success opening the Fortran initialized command window from: Start->Intel Parallel Studio XE 2015->Compiler and Performance Libraries->Command Prompt with Intel Compiler->Intel64 Visual Studio mode, which initializes all the Fortran environment variables.
I expect Fortran XE 2016 would work too, but haven't had a chance to run a case. I have been using Intel Fortran XE 2015 to successfully run Abaqus analyses with user subroutines, so I'm pretty sure that you don't need to get a specific older version of Fortran. Is passing the install verification important to you? Or could you skip the verification and proceed to running a specific Abaqus analysis with a specific user subroutine? I generally skip spending time getting the Abaqus install verification to pass for the user subroutines, and instead run a specific analysis to test it. It looks like you are running the Abaqus installation verification to check on the user subroutines. Thanks again and I will appreciate any input or guidance These instructions were provided in this document.
C:\Program Files (x86)\IntelSWTools\parallel_studio_xe_2016.0.041\compilers_and_libraries_2016\windows\bin\intel64 C:\Program Files (x86)\IntelSWTools\parallel_studio_xe_2016.0.041\compilers_and_libraries_2016\windows\binįinally, I add this line in the abaqus.bat file and ifortvars.bat intel64 vs2015 Third, I modified the variable “path” in system variables. Second, I located the path for ifortvars and ifort which in my case wereĬ:\Program Files (x86)\IntelSWTools\parallel_studio_xe_2016.0.041\compilers_and_libraries_2016\windows\binĬ:\Program Files (x86)\IntelSWTools\parallel_studio_xe_2016.0.041\compilers_and_libraries_2016\windows\bin\intel64
MANUAL ABAQUS 6.14 TRIAL
I downloaded a trial version of Intel Parallel Studio XE 2016.
MANUAL ABAQUS 6.14 PROFESSIONAL
First, I did Install Abaqus and Visual Studio Professional 2015.
0 kommentar(er)
